BEguided
What BEguided does
BEguided designs guide RNAs (sgRNAs) for CRISPR base editors. For every target you supply and each base editor you select, it searches for nearby PAM sites, predicts which editable window (relative to the PAM) the base falls into, scores the guide and annotates bystander editing.
Upload a targets file (TSV / CSV / XLSX) using the field above to get started. Use the Template button to download a sample.
Spreadsheet input
Provide a Spreadsheet of genomic targets you want to edit. BEguided will design guides for all targets provided and base editors selected. Target bases not present in the genome will be replaced with the target base.
The position column is 1-based:
position 1 is the first nucleotide of the chromosome, position 2
the second, and so on. The value is the genomic coordinate of the
base you want to edit.
Required columns:
chromosome— e.g.chr1position— 1-based genomic coordinate of the target basetarget_base— base you want to edit (A,C,G,T)desired_base— base you want to have after editing (A,C,G,T)
The tool picks a base editor profile that supports the
target_base → desired_base change. If some
targets have a change that no profile in the selected group
supports, they are removed from the input with a warning and the
run only processes the remaining targets. Selecting a broader
base editor group brings removed targets back — the check
always re-runs on the original file. If no target at all is
compatible, nothing is run.
Sequence input
Instead of a targets file you can paste one or more sequences
directly. Switch the input mode at the top to
Sequence, then mark the desired edit with a bracket
like [A>G] (or [T>C],
[C>T], [G>A]). The bracket
becomes the base at that position — text after
] shifts one position later in the resulting
sequence.
Example: ATAG[T>C]GAC gives a 9-nt stripped
sequence ATAGTGAC where position 5 is
T (from the bracket) and positions 6…9
are G, A, C. The base
you want to edit goes on the left side of >.
A single sequence without a FASTA header gets the chromosome
name custom; with a FASTA header (anything after
> up to the first whitespace) the header is
used as the chromosome name. In sequence mode the loaded
reference genome and bystander annotation are not used —
guides are designed directly on the provided sequence.
Off-target checking is opt-in for sequence results: pick the reference genome in the Off-target check controls on the Results tab. Because the pasted sequence's location in that genome is unknown, the on-target site cannot be excluded from the search — if your sequence comes from the searched genome, the worst hit found would in many cases be the on-target itself (a perfect match), while for plasmids or inserts that are not in the genome all reported hits are genuine off-targets.
Single target input
For a single target you can skip file preparation entirely:
switch the input mode to Single and fill in the fields
— the chromosome (e.g. chr1,
1, X, Y), the 1-based
position of the base you want to edit, and the
editing direction (A to G, C to T,
G to A, T to C).
A single-target run behaves exactly like a spreadsheet run: guides are designed against the selected reference genome, with bystander annotation and the off-target check available. Target bases not present in the genome are replaced with the target base.
Available base editor profiles
Editing windows are position ranges, counted from the PAM-distal end of the guide, where the base editor is active. General = the full window where some editing occurs; High-activity = the narrower window where editing is most efficient. The full profile table lives on the Base Editors tab, where you can also upload a custom profiles spreadsheet.
Base editor profiles
The default and custom profiles currently available are shown below. Uploading a custom XLSX adds its profiles to the multi-select in the top bar (under a dedicated Custom group). Custom profile names must not collide with default ones. The custom base editor upload is limited to 10 profiles.
Loading base editor profiles…
* Marks an assumed variant based on the SpCas9 version (e.g. SpCas9-NG, SpRY). The editing window is a direct copy from the SpCas9 profile and may differ; functionality of these variants is not certain.
Constraints for uploads: XLSX (or TSV) with the columns
name, editing,
general_edit_start, general_edit_end,
high_edit_start, high_edit_end,
pam; at most 10 profiles; PAM at most 6 bases;
file size at most 1 MB.
Upload a targets file to preview input data.
Results will appear here after the pipeline completes.
Summary will appear here after the pipeline completes.
The off-target report appears here after you run the off-target check on the filtered guides (button in the filter bar above the results). The pass/fail verdict for each guide is shown directly in the Guides table.